Maintaining Mission Critical Systems in a 24/7 Environment. Peter M. Curtis

Чтение книги онлайн.

Figure 3.6 Electronic Ballast

      (Courtesy of Antron Electronics Co., Ltd)

      3.11.3 DC Storage Options

The fact that electrical energy is most easily stored in batteries as DC is the primary reason power conversions is necessary when AC distribution is used in the data center. The two types of batteries that are most commonly used in conjunction with a UPS are lead‐acid wet cell (flooded) and valve regulated lead‐acid (VRLA) or variations thereof. Lithium ion batteries are gaining popularity since they have excellent weight to power density, can cycle or discharge many times without losing capacity, do not off gas during charging, and have a longer life than VRLA’s. They are mainly being deployed on smaller UPS’s below 300kW, and some state or local city codes have special requirements or are hesitant to allow them to be installed in buildings since they are a newer and thought of as unproven. This will change over time as more and more installations become common. For additional information, see Chapter 10 – UPS.

      Another storage technology are flywheels that store kinetic energy and can discharge DC power to a UPS. Conventional batteries and flywheels are covered in more detail in the UPS chapter. Also worth mentioning here are some new battery storage technologies called Zinc‐Bromine Flow Batteries and a megawatt‐class of batteries that use a sodium‐sulfur electrolyte – which are both, by nature, DC sources. Both of these batteries have the potential to be used in grid‐storage class applications and may undergo many deep discharges without suffering ill effects.?? Various battery manufacturers are developing battery storage banks so that excess power produced from solar panels or other renewable sources during the day can be used at night, or other sources like hydropower can charge batteries at night for discharge during peak daytime hours reducing demand loads on fossil fuel plants. For additional information, see Chapter 10 – UPS.

      As of this writing, sodium‐sulfur batteries have already been installed at several locations globally, including a wind farm in Japan and a bus depot in Garden City, NY. Zinc Bromide batteries have yet to prove themselves in anything more than a handful of demo installations, but the technology seems promising for the storage of electricity from intermittent sources and load‐leveling applications, similar to sodium‐sulfur batteries.

      3.11.4 Renewable Energy Integration

      Solar power is the most common renewable resource that can be used for the on‐site generation of electrical power for a data center. Since photovoltaic (PV) arrays produce DC electricity, it is easily integrated with a DC distribution system. Only a voltage regulator is required, or a charge controller if the PV array is used to charge battery storage.

Wind power is another option. Inverter‐based wind turbines already produce AC power. The power conversion that would normally be needed to convert the DC to AC is not required, eliminating the inverter and any need for synchronization.

      Although technically not a renewable energy source, fuel cells are being used to convert natural gas to electrical power locally at data centers and other sites. The output power is synchronized with the utility service and feeds the data center loads through the same distribution. Multiple units can be paralleled to feed a building. Some advantages are that fuel cells are very efficient and will continue providing base power at night when solar panels cannot, or winds die down, and wind power is not fruitful. Another advantage is that excess heat is produced in the conversion cycle that can be used for heating or hot water in the building or used to feed an absorption chiller. Several cons include a natural gas service of sufficient size is required at the site or a tank farm with liquid propane, or other hydrogen‐rich fuel is needed, they are relatively heavy and need to be located outdoors or in a remote structure.

      3.11.5 DC and Combined Cooling, Heat & Power

      Combined Cooling, Heat & Power (CCHP), also known as cogeneration, is an ideal strategy for improving data center energy efficiency. This is accomplished by using some form of power generation equipment that also produces thermal energy as a by‐product. Since data centers typically require 24x7 cooling, the recovered thermal energy can be used to activate absorption chillers that turn the waste heat into free cooling.

      There are two types of power generating equipment that can be easily integrated with a DC distribution system. One is a fuel cell. The fuel cell is an electrochemical device that produces DC electricity, much like a battery. Only a voltage regulator is needed to match the DC voltage of the fuel cell to the DC distribution voltage or an inverter to create AC power that can be synced to a building’s electrical supply or used independently. Since the chemical reaction within the fuel cell produces heat, this thermal energy can be recovered and used to drive an absorption chiller.

Figure 3.7 Absorption Chiller

      (Courtesy of Yazaki Energy Systems, Inc.)

Figure 3.8 Typical Fuel Cell

      (Courtesy UTC Power)

      The microturbine is another prime mover that can produce DC power. Microturbines operate on the Brayton cycle to rotate a small permanent magnet alternator at very high rpm to generate high‐frequency AC, which is rectified to DC. A voltage regulator can be used to match this DC to the DC distribution voltage, or an inverter can convert the DC power to 60hz AC. The turbine exhaust can be run through a heat recovery absorption chiller to make chilled water.

      Figure 3.9 Microturbine CCHP System

      (Courtesy UTC Power)

      3.11.6 Safety Issues

      One СКАЧАТЬ