Maintaining Mission Critical Systems in a 24/7 Environment. Peter M. Curtis

Чтение книги онлайн.

СКАЧАТЬ is being protected. Transformer inrush points must be included to verify that the protective device feeding the unit will not operate when the transformer is energized. Device selection and settings from the database are reviewed to determine if changes are required to improve coordination. If so, settings or selection are modified, and the resulting TCC’s are printed for inclusion in the report. Protective device settings and selections are also summarized in tabular form.

      Figure 3.3 Sample TCC Curve Analysis

      (Source: Courtesy of PMC Group One, LLC)

      In many cases, protective device coordination is a matter of compromise. Rather than being a choice of black or white, device coordination requires making selections that result in the best coordination that can be achieved with the devices that are installed: fuse characteristics are not as varied as electronic trip devices; instantaneous elements in series cannot be reliably coordinated; transformer protection must be selected to provide protection from damage from a fault while passing inrush current when the unit is energized.

      Luckily, where power system reliability must be maximized, and therefore strict coordination is required, electronic relays and trip devices offer a variety of settings, curve shapes, and other functions that allow the system protection engineer to achieve this goal. Electronic relays come with a variety of trip characteristic curves, which, along with time delay and pick‐up settings, allow a great deal of flexibility when programming the device. The Zone Selective Interlocking feature available in many static trip devices allows the arming of Instantaneous settings on breakers in series without losing coordination. The upstream breaker trip device (such as the main device on a bus) communicates with downstream breakers. If the downstream device sees a fault current event, it sends a signal to the main device to block tripping the main breaker, thus allowing the downstream device to operate, minimizing the extent of the electrical system affected by the fault.

      As discussed, state‐of‐the‐art protective devices can make a significant contribution to protective device coordination, minimizing or eliminating unnecessary outages due to compromised coordination. If project requirements demand strict coordination, electrical equipment selection may be affected. It is, therefore, important to consider how these requirements affect equipment selection, specification, and layout as early in the project as possible. The selection of the wrong type of equipment may negate the ability to take advantage of the technological advances discussed above.

3.11 Introduction to Direct Current in the Data Center

Years ago, the Direct Current Data Center gained significant interest due to its ability to operate more efficiently, although today, it is still relevant, it has not been scaled as we thought it would. That being said, all of our modern electronic equipment today relies on solid‐state semi‐conductor technology, which will only operate on direct current, or DC. According to the Green Buildings Forum, 72% of the energy used in the U.S. is consumed in commercial real estate buildings. A study by the University of Virginia shows that 80% of this energy is used by semi‐conductor technology, which means this much AC power must be converted to DC. The 2007 EPA “Report to Congress on Server and Data Center Energy Efficiency” shows that data centers in the United States have the potential to save up to $4 billion in annual electricity costs through more energy‐efficient equipment and operations. One movement to accomplish this that is currently gaining acceptance among data center designers, and garnering support from the Electric Power Research Institute (EPRI), is the use of a direct current distribution system.

      When we step back and look at the end‐to‐end power distribution in a conventional data center, we see several power conversions taking place. Incoming AC utility power is first rectified to DC at the UPS for the purpose of connecting to DC battery storage. It is then inverted back to AC for distribution to the server racks. At the racks, the AC is then rectified back to DC again in the power supplies for each server. We ask ourselves ‐ are all these back‐and‐forth conversions really necessary? The answer is “No.”

      3.11.1 Advantages of DC Distribution

      Suppose we made only one conversion of the incoming AC to DC at the UPS, and then distributed the DC throughout the facility without any further conversions, thereby eliminating two power conversions along with the attendant losses. Not only would this make for a more efficient system, it would also reduce the number of components, thereby eliminating points of failure, making for a more reliable system. As an example, a 380VDC distribution system will result in a 200% increase in reliability, a 33% reduction in required floor space and a 28% improvement in efficiency over conventional UPS Systems, or a 9% improvement over ‘best in class’ AC UPS architectures. A DC distribution system would also facilitate the integration of on‐site DC‐generating power sources, such as solar PV arrays, wind power, and fuel cells, which all can provide DC power without a single power conversion. For example, the best published efficiency for a fuel cell is 50%. According to UTC Power, by eliminating the AC power conditioning subassembly and utilizing waste heat in a combined cooling, heating, and power application, efficiencies can exceed 85% with a high load factor.

Figure 3.4 below shows the various power conversions that are required in a conventional AC distribution system, along with those that are required to connect alternate energy sources.

Figure 3.4 Traditional AC Distribution

Figure 3.5 below shows the fewer conversions that are required with a DC distribution system and the simpler integration of alternate energy sources.

Figure 3.5 DC Distribution

This kind of DC distribution system can provide up to a 25% decrease in energy usage when compared to a traditional AC power distribution system by eliminating the losses associated with the inefficiencies of power conversion equipment. It also reduces the initial cost for electrical distribution equipment by about half. And since there are fewer conversions from AC to DC and DC to AC, which translates into less equipment, the distribution system occupies significantly less space. Proponents of DC power in data centers tout fewer single points of failure in DC systems due to the reduction in components. There is also the accompanying decrease in heat production. This reduces cooling capacity requirements and provides further reductions in operating costs.

      3.11.2 Lighting Updates

      Besides all of the electronic equipment that is found in the data center, another significant consumer of electricity is the lighting system. Fluorescent lighting was the defacto standard for many, many years, and is typically fed with 277VAC in larger commercial buildings or data centers. Since fluorescent lamps vary by type and length, they operate on varying voltages and currents. A fluorescent ballast is used to adjust the supplied voltage and regulate current accordingly. In an effort to improve fluorescent lighting efficiency, the electronic ballast was invented in the 1970s. Besides adjusting the supplied voltage, electronic ballasts also changed the frequency from 60 Hz to 20,000 Hz or СКАЧАТЬ