Integration of Renewable Energy Sources with Smart Grid. Группа авторов
Чтение книги онлайн.
Читать онлайн книгу Integration of Renewable Energy Sources with Smart Grid - Группа авторов страница 11
Название: Integration of Renewable Energy Sources with Smart Grid
Автор: Группа авторов
Издательство: John Wiley & Sons Limited
Жанр: Физика
isbn: 9781119751885
isbn:
Figure 1.5 Parabolic dish system.
Figure 1.6 Linear Fresnel system.
Sometimes, the output yield is very low in this Fresnel system and so Fresnel reflectors with ray tracing was introduced to yield maximum output.
1.1.2 Wind Energy
In the current scenario, the wind energy system is one of the fastest-growing renewable energy. Wind turbine capacity has increased over time. In 1985, typical turbines had a rated capacity of 0.05 megawatts (MW) and a rotor diameter of 15 meters. Today’s new wind power projects have turbine capacities of about 2-MW onshore and 3- to 5-MW offshore. Commercially available wind turbines have reached 10-MW capacity, with rotor diameters of up to 164 meters. The average capacity of wind turbines increased from 1.6 MW in 2009 to 2 MW in 2014 [7].
Wind energy conversion system (WECS) comprises of a wind turbine, gearbox, generator, converter, and transformers as shown in Figure 1.7. The wind energy or the kinetic energy is converted to mechanical energy using a wind turbine. The mechanical energy input is given to the generator and converted into electrical energy. Permanent magnet synchronous generator, Squirrel cage induction generator or doubly fed induction generator can be used in the WECS. The AC output from the generator is converted to a required form using power electronic converter. It is then connected to grid through to a step-up transformer.
Figure 1.7 Wind energy conversion system (WECS).
The wind energy is captured by the rotor blades and transferred to rotor hub. The rotating shaft provides mechanical energy input to the generator, which is further converted into electricity. The gear box helps in increasing the rotational speed of the shaft for the generator. The power extracted by the rotor blades may be expressed as follows:
where α is perturbation factor, ρ is density of the air, A is swept area of the blades, and uo is speed of the upstream wind.
The wind turbines are largely classified into Horizontal Axis Wind Turbines (HAWT) and Vertical Axis Wind Turbines (VAWT). As the name implies, the HAWT has their blades rotating on an axis parallel to the ground. If the blades are placed in such a way that their rotational axis is perpendicular to the ground, it is called as VAWT. The HAWT can capable of producing more electricity as compared to VAWT. It is because the HAWT has more swept area than VAWT. Hence, the HAWT is generally preferred for commercial WECS. However, VAWT is used for small power applications.
1.1.3 Fuel Cell
In search of a clean energy source in the current energy sector, fuel cell has gained its importance. Fuel cell uses hydrogen as a fuel and the energy companies have started concentrating on low carbon hydrogen production. The industries have started using electrolyzer to produce clean hydrogen. In recent years, the electrolyzer installation has increased considerably. The survey says that 350,000 tonnes of low carbon hydrogen production has taken place by the end of year 2019 and 20 other new projects have been targeted by 2020. Fuel cell plays a vital role in generating electricity by using hydrogen as fuel. The more the hydrogen, the more the power. It is similar to a battery in some aspects but can supply energy for a long period of time and it is due to the continuous supply of fuel and oxygen to produce power. Due to these factors, fuel cell finds its application in satellites, manned spacecraft, and other relevant areas. It is also a type of RES that works on the principle of electrochemical reaction that converts chemical energy into an electrical energy. It converts the chemical energy of a fuel, namely, the hydrogen and an oxidizing agent, the oxygen, into electricity.
Figure 1.8 shows the diagram of a fuel cell. A fuel cell consists of an anode, cathode, and an electrolyte membrane. Hydrogen fuel is passed through the anode of a fuel cell and oxygen through the cathode. The hydrogen is split into electrons and protons at the anode side. The protons will pass through the membrane to the cathode side and the electrons are made to flow through an external circuit connected to the load After passing through the circuit, the electrons combine with the protons along with oxygen in air and produces water and heat as their by-product. Fuel cells are very clean as they use pure hydrogen as fuel. The efficiency of the fuel cell is high when compared to conventional techniques like steam turbine and internal combustion engine. The efficiency of a fuel cell can further be increased by interfacing it with a combined heat power system. The waste heat generated from the fuel cell can be used for various applications.
The types of fuel cell are as follows:
1 Proton exchange membrane (PEM) fuel cell
2 Direct methanol fuel cell (DMFC)
3 Alkaline fuel cell (AFC)
4 Phosphoric acid fuel cell (PAFC)
5 Molten carbonate fuel cell (MCFC)
6 Solid oxide fuel cell (SOFC)
7 Reversible fuel cell
Figure 1.8 Diagram of a fuel cell.
1.1.3.1 Proton Exchange Membrane Fuel Cell
The frequently used fuel cell is PEM fuel cell. Figure 1.9 shows the PEM fuel cell. It is a light weight fuel cell and delivers high power density. It is also called as polymer electrolyte membrane (PEM) fuel cell [8]. It consists of carbon porous electrodes with solid polymer as an electrolyte and platinum as a catalyst. It operates with hydrogen, oxygen and water. Hydrogen fuel is given as an input from storage tanks. It operates at low temperatures and so considered as a durable one. A good catalyst is used but platinum is not so economical and it is sensitive to carbon monoxide poisoning. It requires a reactor to eradicate this poisoning effect and hence the cost also increases. Since it operates at low temperatures, its start-up time is very quick, and hence, it is suitable for automotive applications.
1.1.3.2 Direct Methanol Fuel Cell
Most of the fuel cells use hydrogen as the fuel to generate electricity, However, DMFC use methanol as a fuel input along with water. Methanol has higher energy density than hydrogen and it is easy to transport as it is like a liquid and similar to gasoline. It is a dense liquid but considered as a stable one. Its efficiency is around 40% and the operating temperature is between 50°C and 120°C. It is used as a powering circuit СКАЧАТЬ