The Barnet Book of Photography: A Collection of Practical Articles. Various

Чтение книги онлайн.

СКАЧАТЬ has an important influence on development, the time required for the first appearance of the image and for the completion of development being, as a rule, less the higher the temperature. Further, if the developing solutions are very cold, it is often almost impossible to obtain sufficient opacity.

      Perhaps the most difficult thing in connection with development is to know when to stop the process, that is to say, when the image has acquired sufficient opacity, or "density," as it is often called. After all the required detail has become visible, the plate from time to time is lifted carefully out of the developer, allowed to drain for a moment or two, and then held between the developing lamp and the eye; the opacity of the image, especially in the highest lights and deepest shadows, being carefully scrutinised. The appearance of the image as seen when looking at the back of the plate, is also carefully observed.

      For this purpose it is very much better that the light of the developing lamp should pass through transparent glass (ruby or deep orange) so that the flame itself is distinctly visible, instead of through ground glass or a coloured translucent fabric. Further, the flame of the lamp, whether gas or oil, should always be turned up to the same height, for it is clear that if the brightness of the flame used for making the examination is not fairly constant, all sorts of variable results will be obtained. For this reason it is much better to judge the opacity of negatives by artificial light than by daylight, the intensity of the latter being so variable. A paraffin lamp with a circular wick and a deep ruby chimney with a metal cap at the top, answers admirably.

      No general rules can be laid down; the appearance of the properly developed image depends on the thickness of the film, the granularity of the silver salt, the presence or absence of silver iodide, and the composition of the emulsion used. Experience only is of value, and the best way to secure uniformly satisfactory results, is to keep as far as possible to one brand of plates. With some plates, for example, very little of the image should appear at the back of the plate, with others the greater part of the image must be distinctly visible there.

      Sometimes, especially when using small sizes of plates, it is not easy to tell whether all the necessary detail in the shadows has been brought out, and this is an important matter, for if the small negatives are to be used for making enlarged negatives or prints, or lantern slides, there should be very little clear glass indeed even in the deepest shadows of the subject. As a rule it may be said that when every part of the image is at least gray the maximum possible amount of detail has been brought out. If the greyness begins to spread to the margins of the plate where it has been protected by the rebate of the dark slide, general fog is being produced, and, as a rule, little will be gained, but much may be lost, by continuing the development for any considerable time after this is observed. When development is completed the developer is poured off, the plate is well rinsed under the tap or in two or three changes of water, and is then ready for fixing.

      DEVELOPMENT WITH PYRO-AMMONIA.

This method of development has the advantage that the constituents can be kept in concentrated solutions, considerable modifications in the composition of the developer can be made very readily and the negatives obtained are of excellent printing quality. On the other hand it cannot be satisfactorily employed with certain brands of rapid plates, because with them it has a tendency to produce general fog, and with some other plates, especially when they are old, it has a tendency to produce what is known as green fog.

      Three solutions are prepared:—

Reducer.
Pyrogallic acid	1	oz. or	10	parts
Potassium metabisulphite1	1	oz. or	10	parts
Water, to make up to	10	oz. or	100	parts
Accelerator.
Ammonia	1	oz. or	10	parts
Water, to make up to	10	oz. or	100	parts
Restrainer.
Ammonium bromide	1	oz. or	10	parts
Water, to make up to	10	oz. or	100	parts

[1] The metabisulphite is dissolved in about 8 oz. (80 parts) of water with the aid of heat, and the pyrogallic acid is then added. When the liquid has cooled it is made up to 10 oz. (100 parts) by addition of water, the whole being well mixed by shaking.

      For each ounce of developer, take 20 minims of reducer, 20 minims of restrainer and 40 minims of accelerator, and make up to 1 oz. with water. With some plates 60 minims of accelerator and 30 minims of restrainer may be used, but any greater proportion of accelerator has considerable tendency to produce general fog. On the other hand the proportion of restrainer can often be increased with advantage since, unless the amount added is very large, its chief effect is to prevent general fog; 30 minims of restrainer to 40 minims of accelerator, or 40 minims of accelerator to 60 minims of restrainer are proportions that can be recommended. Too low a proportion of bromide should be carefully avoided.

      It is very important to ascertain, by careful trial with each brand of plates that is to be used, what is the maximum proportion of ammonia that can safely be added, and what proportion of bromide to ammonia is necessary in order to prevent general fog. As a rule, the more rapid the plates the smaller is the quantity of ammonia that can be used with safety.

      By far the best plan is to keep development well under control by adding only part of the accelerator at the beginning of development and adding the rest as circumstances require.

      For each ounce of developer take 20 minims of pyro solution and make up to the required bulk with water. In another measure mix for each ounce of developer 40 minims of bromide solution and 60 minims of ammonia solution, and regard this as the maximum quantity that can be added with that bulk of developer. Now to the diluted pyro solution add about a quarter or one-third of the ammonia and bromide solution, pour this mixture on the plate and observe what happens.

      If the mode of appearance of the image indicates that the plate has been correctly exposed, about half the remaining ammonia and bromide mixture may be added to the developer at once, and the action allowed to continue, with occasional rocking of the dish. If development proceeds satisfactorily and, in particular, if the chief details in the shadows begin to appear before the highest lights have become too opaque, it is not necessary nor advisable to add the last portion of the ammonia and bromide mixture, since the tendency to general fog and green fog is reduced when the proportion of ammonia is kept as low as possible. On the other hand, if the development flags and the appearance of shadow detail is a little tardy, the rest of the ammonia and bromide mixture must be added.

СКАЧАТЬ