The Gun Digest Book of Firearms Assembly/Disassembly Part IV - Centerfire Rifles. J B Wood
Чтение книги онлайн.
Читать онлайн книгу The Gun Digest Book of Firearms Assembly/Disassembly Part IV - Centerfire Rifles - J B Wood страница 3
Название: The Gun Digest Book of Firearms Assembly/Disassembly Part IV - Centerfire Rifles
Автор: J B Wood
Издательство: Ingram
Жанр: Спорт, фитнес
isbn: 9781440224195
isbn:
Sights: Nearly all dovetail-mounted sights are drifted out toward the right, using a nylon, aluminum, or brass drift punch.
1. The tiniest of these fine German instrument screwdrivers from Brownells is too small for most gun work, but you'll see the rest of them used frequently throughout the book. There are many tight places where these will come in handy.
2. When a larger screwdriver is needed, this set from Brownells covers a wide range of blade sizes and also has Phillips- and Allen-type inserts. The tips are held in place by a strong magnet, yet are easily changed. These tips are very hard. W ith enough force you might manage to break one, but they'll never bend.
3. You should have at least one good pair of bent sharp-nosed pliers. These, from Brownells, have a box joint and smooth inner faces to help prevent marring.
4. For heavier gripping, these Bernard parallel-jaw pliers from Brownells have smooth-faced jaw-pieces of unhardened steel to prevent marring of parts.
5. For situations where a non-marring rap is needed, this hammer from Brownells is ideal. It is shown with nylon faces on the head, but other faces of plastic and brass are also available. All are easily replaceable.
6. For drifting out pins, these small all-metal hammers from B-Square are the best I've seen. Two sizes (weights) are available and they're well worth the modest cost.
7. For situations where reach and accessibility are beyond the capabilities of sharp-nosed pliers, a pair of large sharp-nosed forceps (tweezers) will be invaluable. From Brownells.
8. One of the most-used tools in my shop is this nylon-tipped drift punch, shown with an optional brass tip in place on the handle. It has a steel pin inside the nylon tip for strength. From Brownells, and absolutely essential.
9. A good set of drift punches will prevent a lot of marred pins. These, from Brownells, are made by Mayhew. The tapered punches at the right are for starting pins, the others for pushing them through. Two sizes are available—4 inches or 6 inches.
10. These punches by Mayhew are designed specifically for roll pins and have a projection at the center of the tip to fit the hollow center of a roll pin, driving it out without deformation of the ends. From Brownells.
11. Some of the necessary tools are easily made in the shop. These non-marring drift punches were made from three sizes of welder's brazing rod.
12. This heavy wrench from Brownells is designed specifically for removal of the barrel nut in Remington Model 742 and Model 760 rifles. It's a quality tool of 01 steel, hardened to Rockwell C 46–48.
13. Most Remington centerfire rifles have the extractor mounted inside the front of the bolt by a tiny rivet. This special tool from B-Square will set these rivets with a minimum of trouble.
14. These extractor pliers are used in both the removal and replacement of Mauser or Springfield-type extractors, making a difficult job much easier. From Brownells.
15. These wrenches are designed for removal of the piston nut in the .30 U.S. Carbine. The tool at the right is the original military type with three lugs, and the one at the left is a double-end type, to fit both the military guns and the two-slot nut found on some commercial civilian Carbines. These wrenches are available from several military surplus and commercial sources.
16. Without this tool, removal of the firing pin, ejector and extractor from the 30 U.S. Carbine is a tedious job. It is available from military surplus sources.
17. This combination tool for the U.S. M-1 rifle (Garand) has provisions for cleaning the chamber, installing the extractor and ejector in the bolt, a screwdriver, and other features. A completely-equipped Garand has one of these in the storage trap in the buttstock. They are available from military surplus sources.
Argentine Model 1891 Mauser
Similar/Identical Pattern Guns
The same basic assembly/disassembly steps for the Argentine Model 1891 Mauser also apply to the following guns:
Argentine Model 1891 Carbine
Spanish Model 1891 Rifle Turkish Model 90T
Belgian Model 1889 Rifle, Carbine
Turkish Model 1890
Yugoslavian Model 90T
| Data: | Argentine Model 1891 |
| Origin: | Germany |
| Manufacturer: | Ludwig Loewe, Berlin, and Deutsche Waffen und Munitionsfabriken |
| Cartridge: | 7.65mm Mauser |
|
Magazine capacity:
СКАЧАТЬ
|