Banjo For Dummies. Bill Evans
Чтение книги онлайн.

Читать онлайн книгу Banjo For Dummies - Bill Evans страница 15

Название: Banjo For Dummies

Автор: Bill Evans

Издательство: John Wiley & Sons Limited

Жанр: Музыка, балет

Серия:

isbn: 9781119731405

isbn:

СКАЧАТЬ your ears to get your instrument in tune. You have a banjo; now you can get to work on training your ears!

      

Even pro players follow up on their initial pass at relative tuning by trying different pairs of strings to hear what they sound like together and tuning the adjacent pairs of strings a second time. If one or more strings are severely out of tune to begin with, you definitely need to repeat the processes I describe in the following sections once or twice until the banjo is in good tune.

When tuning from low to high, you begin with the lowest-pitched 4th string and work your way up to the 5th string, the highest-pitched string. Using the following instructions, you tune the remaining four strings up from the 4th string, using the left-hand middle finger to fret each reference note. For now, try striking (or picking) each string with a downward motion of your right-hand thumb. You can watch me demonstrate relative tuning from low to high in Video Clip 1. I name and play all the open strings on the banjo in G tuning.

      

When you're comparing the pitches of two strings as you work through the following steps, your goal is to match the pitch of the open string to the fretted string that you pick. If the open string sounds higher in pitch, that string is sharp, and you want to adjust the tuning peg for that string in the direction that brings its pitch down (usually clockwise for the 3rd and 4th strings; counterclockwise for the 1st and 2nd strings). If the open string is lower in pitch, that string is flat; in this case, you rotate the peg in the direction that causes the pitch of the string to rise (usually counterclockwise for the 3rd and 4th strings; clockwise for the 1st and 2nd strings).

      1 Pick the 4th string fretted at the 5th fret and compare its pitch to the open 3rd string.You may need to strike the fretted 4th string first, wait a moment to hear its pitch, and then strike the 3rd string to listen to its pitch. Does the 3rd string (the second note you play) sound higher or lower than the 4th string? Try singing the two pitches to feel whether the pitch rises or falls.

      2 Using the tuning peg, adjust the pitch of the 3rd string up or down until it matches the pitch of the fretted 4th string.When the pitches of the two strings match each other, the 4th and 3rd strings of your banjo are in tune.

      3 Pick the 3rd string fretted at the 4th fret and match the open 2nd string to this sound.After these strings sound the same, you have the 4th, 3rd, and 2nd strings of your banjo in tune.

      4 Pick the 2nd string fretted at the 3rd fret and tune the open 1st string to this sound.

      5 Pick the 1st string fretted at the 5th fret and tune the open 5th string to this sound.Remember that the 5th string is the short string on your banjo that's located on the opposite side of your neck from the 1st string. Some banjos have 5th-string tuning pegs that are difficult to turn without causing wild fluctuations in pitch. Don't worry if it takes a bit more time to get the 5th string in tune.

       Your reference point is always a fretted string when tuning from a lower- to a higher-pitched string. You need to lift the left hand up to adjust the tuning peg of the string you're attempting to tune and then fret it again on the lower string to play the reference pitch.

       If you make a slight error at the beginning of this process, that mistake is exaggerated as you proceed to try and tune the rest of the strings. You may have to start all over.

      

If you're having difficulty determining whether a string is sharp or flat, tune it down until the string is obviously below the pitch of your reference note. Then gradually bring the string you're trying to get in tune up in pitch to match the reference note.

      Relative tuning is great when you're playing by yourself or for quickly touching up a string or two in the middle of a practice session. However, when playing with others (or with the audio tracks and video clips that accompany this book, available at www.dummies.com/go/banjo), you need to get accustomed to tuning your banjo using one or more outside reference notes as provided by an electronic tuner or another instrument. I explain how to tune by using reference notes in the following sections.

      

If you’re practicing on your own, the source of your reference pitches doesn’t matter; the important thing is to have the banjo in tune with itself. If you’re playing with others, everyone should use the same reference pitch, whether it comes from an electronic tuner or an instrument.

      Using an electronic tuner

Photo depicts an electronic clip-on tuner which makes tuning easier.

      Photograph courtesy of Elderly Instruments

      FIGURE 2-2: Using an electronic clip-on tuner makes tuning easier.

      

If the string is significantly out of tune, the tuner may assign an alphabet letter that isn't a G, B, or D (check out the section on G tuning a few pages back in this chapter for the skinny on the notes used in this tuning). I've been avoiding it up to now, but so you aren't thrown off by these various letters, you should know the following order of notes in music:

      G / G♯ or A♭ / A / A♯ or B♭ / B / C / C♯ or D♭ / D / D♯ or E♭ / E / F / F♯ or G♭ / G

       Equivalent notes: You may notice that some notes in the preceding series have an or between them. Without getting too boring, just remember that a G♯ is the same pitch as an A♭, an A♯ is the same as a B♭, and so on. These equivalent notes are found at the same fret on your fingerboard.

       Pitch: As you move to the right in the order of notes, you're naming higher-pitched notes; as you move to the left, the notes are lower pitched.

       Half versus whole steps: If you move one note СКАЧАТЬ