Geophysical Monitoring for Geologic Carbon Storage. Группа авторов
Чтение книги онлайн.
Читать онлайн книгу Geophysical Monitoring for Geologic Carbon Storage - Группа авторов страница 49
Название: Geophysical Monitoring for Geologic Carbon Storage
Автор: Группа авторов
Издательство: John Wiley & Sons Limited
Жанр: География
isbn: 9781119156840
isbn:
(5.13)
Figure 5.10 Comparison between the scCO2 saturations in Frac IIb sample within only the fracture versus the entire core. The saturation within the fracture was determined from CT images. When rapid changes in the Young's modulus and the attenuation occur in Figure 5.8 (core scCO2 saturation ~5%–7%), nearly 50% of the fracture is already saturated with scCO2, although from the CT images, most of the matrix near the fracture is still fully saturated with water. The final saturation of the fracture is also much higher (~83%) compared with the entire core (~17.5%). Note that the second data point in the plot was affected by CT image registration errors near the bottom of the sample.
where the fractor 1/3 is due to the fact the radial total stresses τ 11 and τ 22 are zero. B can be expressed as (e.g., Mavko et al., 1998)
(5.14)
where K f is the bulk fluid modulus for mixed water and scCO2. Also, from equations (5.5) and (5.6), by assuming no fluid motion in the fracture (i.e.,
(5.15)
where we used α F ~ 1 and η M ~ φ F /K f , and φ F ~ 1.
The resulting uniaxial Skempton coefficients B/3 and B F /3 are plotted in Figure 5.11 for a range of scCO2 saturation within the matrix rock and the frac ture. At the initial stage (the fracture and matrix pores are fully water saturated), there is a large difference in the uniaxial Skempton coefficient values, which would result in rapid fluid exchange and energy dissipation. At the intermediate stage, fast passing of scCO2 results in large increases in the scCO2 saturation in the fracture (50% is assumed here) compared with the matrix (0% is assumed). This results in much smaller differences in the Skempton parameters, which indicates much less energy loss from the fluid movement. At the final stage (scCO2 saturations of the fracture 83%, matrix 16.5% [calculated from the saturation of the entire core, 17.5%]), the difference becomes somewhat larger, although much less than the initial stage. Although admittedly this analysis ignores the dynamic effect of fluid flow between a fracture and a matrix, it indicates that the fluid‐substitution‐induced changes in the dynamic pore pressure differences may be responsible for the observed unusual behavior of the dynamic Young's modulus and the attenuation.
Figure 5.11 Changes in the uniaxial Skempton coefficients B/3 and BF/3 during Frac IIb scCO2 injection test. The difference between the fracture and the matrix is proportional to the wave‐induced pressures between them if the fluid within the pores and the fracture is not allowed to move. A large difference at the initial water‐saturated state reduces when the scCO2 saturation of the fracture increases by fast passing of the fluid to the fracture (here, the matrix scCO2 saturation is assumed to be unaffected). In the final stage, the difference between the coefficients recovers to some degree.
When the two mechanisms (near‐monotonic decreases in the modulus and increases in attenuation from the heterogeneous invasion of scCO2 in the matrix, and nonmonotonic changes in the modulus and attenuation from interactions between the matrix and the fracture) are combined, the observed complex behavior of the sample's dynamic properties can be explained. However, dynamic poroelastic modeling of the scCO2‐invasion‐induced dynamic rock property changes would be needed for their quantitative validation.
5.5. CONCLUSIONS
In this chapter, we presented a series of laboratory experiments on the seismic property changes of fractured Carbon Tan sandstone cores during supercritical CO2 injection. The use of a modified resonant bar technique (Split‐Hopkinson Resonant Bar method) allowed us to make the measurements at crosshole seismic survey frequencies, at approximately 1.4–1.5 kHz for longitudinal waves (or Young's modulus) and 800–900 Hz for torsional waves (or shear modulus). Evolving distributions of water and scCO2 in the samples were also determined via X‐ray CT imaging.
The experiments showed that CO2 injection resulted in little to no changes in the overall Young's modulus of the sample when the fracture was highly compliant and parallel to the core axis. In contrast, samples containing a core‐perpendicular fracture exhibited large decreases in the Young's modulus, particularly when the leading edge of the invading scCO2 reached the fracture by fast passing along high‐permeability features in the sample. In both cases, large increases in the attenuation were observed. However, the attenuation in the latter samples showed a sudden decrease when the scCO2 reached the fracture, corresponding to the maximum rate of decrease in the Young's modulus.
In our experiments, the pressure diffusion length in water‐saturated, intact rock matrix was a little over 1 cm, and the diameter and the length of the core sample were 3.8 cm and ~10 cm, respectively. This indicates that the fluid‐substitution‐induced changes in the rock's bulk modulus occurred locally within the sample, unless the wave‐induced perturbation of the fluid pressure could propagate along a high‐permeability fracture. We observed the Young’s modulus of a sample with a core‐parallel fracture was insensitive to scCO2 injection. An analysis using a simple, isotropic Gassmann model showed this was possibly attributed to the large (drained) normal fracture compliance, combined with the equalization of the wave‐induced fluid pressure throughout the core, which was facilitated by the fracture. СКАЧАТЬ