Yearn to Burn: A Pyrography Master Class. Simon Easton

Чтение книги онлайн.

      (A) 180- and 240-grit sandpaper; (B) pliers; (C) needle files; (D) screwdriver; (E) ruler; (F) eraser; (G) pencils; (H) craft scalpel/craft knife; (I) pair of compasses; (J) mechanical pencil; (K) tracing paper; (L) masking tape.

      There is a range of basic tools that I always advise any pyrographer to have available when working on their designs. Most of these are used for preparing your designs in terms of the layout or the surface itself and are, therefore, equally as vital as your pyrography machine itself. Below is my list of essential items to consider.

      If you have built up a varied collection of pyrography pens or nibs, make sure that you invest in a suitable container for safe storage. Pens need to be stored so that the nibs do not get damaged while not in use, and individual nibs should be kept safe in a holder that prevents them from becoming inadvertently misplaced or lost between sessions.

      • Pencils, erasers, and sharpeners for drawing out your design. I find mechanical pencils particularly useful for precise work.

      • Measuring tools, including a ruler, pair of compasses, circle stencil templates, protractors, and the like, to ensure your designs are accurate where they need to be.

      • Access to a laptop or computer with a dual-purpose printer/scanner to help with creating layouts at the correct size and scale for transferring.

      • A desk lamp to provide enough light to work by.

      • Tracing paper and masking tape to transfer designs that you use from other sources (and to hold them in place as you do so).

      • Cutting tools such as a good pair of scissors or a crafts scalpel/craft knife. If you use the latter, invest in a quality cutting mat to protect your worktop.

      • Fine grade sandpaper for preparing wooden surfaces or removing marks made in error.

      • A selection of hand tools, including screwdrivers, pliers, needle files, and more, for fitting and adjusting nibs in your pyrography machine.

      It is important to keep your pyrography nibs free of the carbon and grit that builds up as you burn. This can easily be achieved by using the edge of a knife blade, scalpel, pair of scissors, or some other sharp blade. Lightly scrape the blade across the surface of the nib to clear the grit. Fine abrasives such as sandpaper can also be used to gently clean nibs, but care must be taken not to use these excessively, as the nibs will wear down more quickly and eventually break. My preferred option is to use a gentler abrasive alternative such as wire wool or the rear of a metal mesh tea strainer, since these do not wear away the nib surface as quickly. One cheap option that is inexpensive and readily available is a kitchen kettle limescale descaler, since these are made of a fine wire wool and are made in small blocks or rings, making them a handy addition to your workspace.

       Materials for Use

      Pyrography can be used across a range of different materials. Wood is the most traditionally suited to the craft, and this is reflected by the wide range of wooden blanks that are available from both physical and online craft supply retailers. I also enjoy identifying and working with a broad spectrum of woodworkers, such as woodturners, frame makers, and the like. There is no greater pleasure than working on something that has been made to your own specifications for a unique project.

      Certain woods are better suited for use with pyrography than others. Birch, ash, sycamore, and lime are perfect for pyrography because they have a fine or smooth grain, while also proving a good natural contrast to the burned marks through their pale tone. Some hard woods can be used but present their own different challenges due to their heavier grain; for example, oak has a dense, tough, and dark surface that can be used when creating bold monotone designs but isn’t as suitable for delicate lines or soft shading. As well as having a sticky sap residue that bubbles up when burning, pine can be very tricky to use due to the frequent changes in texture from hard to soft as you move across the grain. This can result in uneven lines or marks where the wood resists the burning in one area before burning exceptionally easily in the next. My simple recommendation when you decide to try a new wood type is to obtain a small offcut to practice on first. This should help you to ascertain whether the material is suited for the purpose that you have in mind before you spend any wasted effort attempting a masterpiece that is ultimately doomed to failure.