Inverse Synthetic Aperture Radar Imaging With MATLAB Algorithms. Caner Ozdemir
Чтение книги онлайн.
Читать онлайн книгу Inverse Synthetic Aperture Radar Imaging With MATLAB Algorithms - Caner Ozdemir страница 26
Название: Inverse Synthetic Aperture Radar Imaging With MATLAB Algorithms
Автор: Caner Ozdemir
Издательство: John Wiley & Sons Limited
Жанр: Отраслевые издания
isbn: 9781119521389
isbn:
Figure 2.5 Simulated RCS (in dBsm) of an aircraft model at 2 GHz as a function of azimuth angles.
1 First, the radar signal is generated with the help of the microwave generator (or source).
2 Then the generated signal is transferred to the transmitter by means of transmission lines.
3 The signal is sent out via the transmitting antenna.
4 The radar wave travels in the air and reaches the target.
5 Only some little portion of the transmitted radar signal is captured by the target and reflected back depending on the RCS value of the target.
6 The reflected wave travels in the air, and only a small fraction of the reflected energy reaches back to the radar receiver.
7 The receiver antenna captures some portion of this energy and passes it to the radar receiver.
8 The radar receiver analyzes this scattered signal to obtain the information about the target that may include its location, velocity, direction, RCS, etc.
The radar range equation is the mathematical expression that manifests the analysis of what happens to the signal strength while it goes through the above processes.
2.4.1 Bistatic Case
A conceptual sketch of the above events for the bistatic radar configuration is illustrated in Figure 2.6. First, the microwave generator (usually with a magnetron, klystron, or a traveling‐wave‐tube amplifier) produces the radar signal of Pin watts. This signal is transferred to a transmitting antenna through a transmission line or a waveguide. Because of the finite conductivity of the lines and other microwave components, some of the power is lost during the transmission. Therefore, the power delivered to the transmitting antenna is given by
where L1 is the transmit loss mainly due to finite conductivity of the transmission line or dielectric losses. Once the power is delivered to the antenna, the power radiated by the antenna is
where Γtx is the reflection coefficient at the terminal of the antenna and is given by
(2.15)
In the above equation, Za is the antenna radiation impedance and Zo is the characteristic impedance of the transmission line connected to the terminals of the antenna. The loss, 1/(1 − |Γtx|2) ≜ Ltx, associated by the impedance mismatch at the transmitter, is called the transmitter loss. Of course, if the antenna is matched, the radiated power will be equal to the power transmitted to the antenna as
Figure 2.6 Geometry for obtaining bistatic radar range equation.
(2.16)
When the power is radiated by the transmitting antenna at a particular direction with the antenna gain of G1, power density at the range of R1 (where the target is located) can be found as
(2.17)
The power incident to the target is scattered with an amount of the equivalent echoing area, or simply the RCS of the target. Therefore, the scattered power is then equal to
(2.18)
Then, the power is reradiated by the target as it reaches the receiver antenna located at R2 distance away from the target. The power density of the scattered power around the receiver becomes
(2.19)
At this stage, a very small amount of power is available to the receiving antenna. Therefore, it is crucial to catch as much power as possible by using a large aperture antenna. This implies that it is preferable to use largest practical aperture or reflector to collect as much of the incident power as possible. Antennas capture the incident signals with their effective apertures, Aeff, but not their actual apertures (Balanis 1982). In most antennas, effective aperture sizes are smaller than the actual aperture sizes. The power captured by the receiver antenna is then equal to
(2.20)
Antenna effective aperture, Aeff, can be written in terms of its gain, G2 as (Balanis 1982)
(2.21)
Replacing effective aperture Aeff with the receiver gain G2 in Eq. 2.22 using the relationship in the above equation, one can easily obtain the following equation for the power captured by the receiver as
Some of the captured power is delivered to the transmission line of the receiver if the antenna is not perfectly matched. Then, the received power at the front end of the transmission line is given by
Here, Γrx is the reflection coefficient at the terminal of the receiving antenna and is equal to
(2.24)
In the above equation, Zb is the receiving antenna's radiation impedance, and Zo is the characteristic impedance of the transmission line connected СКАЧАТЬ