Plastics Process Analysis, Instrumentation, and Control. Группа авторов

Чтение книги онлайн.

СКАЧАТЬ additive manufacturing costs by their processes and materials, which were subdivided into ill-structured costs, well-structured costs and product enhancements and quality (11) 2016 In-depth discussion of cost methodology used in product development process. No classification technique proposed. (12) 2016 Covered industrial sector related to the materials and management. Briefly reviewed additive manufacturing costing models (13) 2016 Provided updated estimate of the value related to the supply chain (14) 2016 Described cost models as a subset of design for additive manufacturing (15) 2017 Focused on defense support services and categorized the cost models into intuitive, analogical and analytical approaches (16) 2017 Focused on operation management where the strengths and weaknesses of the models were discussed. Included a general review of additive manufacturing (17) 2019 Provided a broader review on additive manufacturing technologies, additive manufacturing cost models, spare part digitalization and environmental effects for the aviation industry (18)

      In the weld line extension algorithm, 135° is set as a welding angle threshold for forming weld lines. Finally, the effects of cavity thickness, process parameters, and mesh densities have been investigated. Moreover, moldflow simulation results and real parts in production have been conducted to verify the proposed determination method, which demonstrate that the proposed method is correct and effective in actual production (9).

1.6 Extrusion Blow Molding

       1.6.1 Rapid Thermal Cycling Molding

      Blow molded parts made from engineering resins usually possess a poor surface quality, and thus cannot satisfy the requirement of high-gloss appearance in some applications. For this reason, a rapid thermal cycling extrusion blow molding (RTCEBM) technology was developed. The process principle was presented and its process procedure optimization was also analyzed (19).

      With the aim of obtaining a uniform temperature distribution on both the mold cavity and the core surfaces, a two-step optimization method based on a sequential quadratic programming algorithm was proposed for designing the heating system in a RTCEBM mold. Its effectiveness was demonstrated by optimizing the electric-heating system for the RTCEBM mold of an automotive spoiler.

      After optimization, the maximum core surface temperature difference is reduced by 77% from the initial value of 22.06°C to the optimal value of 5.05°C. The molding process coordination could also be ensured. So, an effective method has been assessed to optimize the heating system for these molds with cavity and core sides to be heated simultaneously (19).

       1.6.2 Rapid Heat Cycle Molding

Rapid heat cycle molding (RHCM) is an advanced injection molding technology for producing spraying-free plastic products with excellent appearance (20). Rapid mold heating and cooling is the key technique of RHCM.

      Despite being widely used in practice, the regular rapid mold heating and cooling methods still have some obvious defects. Thus, a new rapid mold heating and cooling method has been developed, characterized by electric heating and annular cooling.

      Here, the temperature and pressure responses in the heating and cooling periods were experimentally investigated (20). The results of the study showed that the tool surface temperature increases almost linearly with the heating time after a short response time. The larger the heating power or the smaller the distance from heater to tool surface, the faster the heating rate.

      The introduction of air bubbles into the working fluid can remarkably reduce the pressure growth of working fluid without affecting the heating rate. In the investigated range of flow rate, the cooling rate first increases significantly with the flow rate, and then reaches a plateau, while the running pressure of working fluid increases linearly with the flow rate in the whole range.

      The optimum flow rate is around 6.0 l min^–1, corresponding to a Reynolds number of 6700 (20). The Reynolds number helps to predict flow patterns in different fluid flow situations. At low Reynolds numbers, flows tend to be dominated by laminar (sheet-like) flow, while at high Reynolds numbers flows tend to be turbulent (21).

      The heat transfer coefficient in the cooling period increases sharply at the initial stage, and then reduces gradually, and finally reaches a plateau. The larger the Reynolds number, the higher the heat transfer coefficient. In particular, the heat transfer coefficient and the Reynolds number show a linear relationship on the double logarithmic scale. Finally, a mathematical model was developed for predicting and controlling the temperature fluctuation range of tool surface (20).

       1.6.2.1 Reduction of Weld Lines

      Rapid Heat Cycle Molding. The RHCM technique can greatly improve weld lines without prolonging the molding cycle. The effects of cavity surface temperature in RHCM on the mechanical strength of the specimen with and without weld line were investigated (22, 23).

      Six kinds of typical plastics, including poly(styrene) (PS), poly(propylene) (PP), acrylonitrile-butadiene-styrene (ABS), ABS/poly(methyl methacrylate) (PMMA), ABS/PMMA/nano-CaCO₃ and glass fiber-reinforced PP, are used in experiments. The specimens with and without a weld line are produced with the different Tcs on the developed electric-heating RHCM system. Tensile tests and notched Izod impact tests are conducted to characterize the mechanical strength of the specimens molded with different cavity surface temperatures. Simulations, differential scanning calorimetry (DSC), scanning electron microscopy (SEM) and optical microscope are implemented to explain the impact mechanism of Tcs on the mechanical properties.

      Thermal cycling experiments are implemented to investigate cavity surface temperature responses with different heating and cooling times. According to the experimental results, a mathematical model was developed by regression analysis to predict the highest temperature and the lowest temperature of the cavity surface during thermal cycling of the electric heating RHCM mold (23).

      The simulated cavity surface temperature response showed a good agreement with the experimental results. Based on simulations, the influence of the power density of the cartridge heaters and the temperature of the cooling water on the thermal response of the cavity surface could be obtained. A high cavity surface temperature during the filling stage in RHCM can significantly improve the surface appearance by greatly improving the surface gloss and completely eliminating the weld line and jetting mark (23).

      Weldless-Type Injection Mold Apparatus. A general forming process of a polymer resin has problems such as an aesthetically poor appearance due to a weld line formed by the molten resin in the mold and a low degree of surface gloss.

      To solve these problems, СКАЧАТЬ