CNC Trade Secrets. James Harvey

Чтение книги онлайн.

Figure 3-2 It’s a good idea for machinists to physically lay out all the tools used in a program in sequential order before installing them in a machine. Most tool numbering errors can be caught early in this way.

      No programmer can provide perfect programs all the time. I’ll even go so far as to say that if I’m the machinist, and I run your program, which results in a crash, it’s my fault. In other words, with few exceptions, I believe the machinist has the responsibility and the means, within reason, to make sure everything is going to run OK.

      Tool numbers get screwed up in programs for various reasons. During program construction, programmers have to decide what tools to use. Tools often get added or subtracted by the programmer. If the programmer fails to renumber the final tool selections in a program, confusion can occur while setting up the job.

      5.Reduce the “Rapid” speed (G00) during setup and debugging by activating a lower rapid speed percentage button.

      Reducing the rapid speed is a precaution that gives you more time to hit the feed hold button if something doesn’t look right. I often use these lower percentages during setup and debugging, especially when I am working on expensive parts.

      6.For first runs and debugging, toggle between the “Cycle Start” button and the “Feed Hold” button on the controller as the cutter approaches the part. (see Fig. 3-3)

      It is difficult to see where a cutter is in relation to a part when the spindle is at Machine Z Zero (retracted). The closer the cutter gets to the part, the easier it is to see the relationship between the part and cutter. Sometimes I toggle half a dozen times when a cutter is on its way down, especially if I’m doing something like engraving expensive mold cavities.

Figure 3-3 The machinist is being careful here by toggling between the cycle start button and the feed hold button as the cutter approaches the part. If there is a programming error, the machinist is in a good position either to catch the error before any material is cut or to reduce the damage the programming error may cause.

      7.Insert M1 “Optional Stop” commands in the program before each tool change. (See Fig. 3-4)

      For first runs and debugging, it is useful to have the “Optional Stop” activated so that you can be at the machine for the start of a new tool. Often, the first few moves a new tool makes will let you know if there is a problem. Once you determine all tools are running okay, you can deactivate the “Optional Stop” button and start running.

      8.Clamp large remnants in place or remove them so they can’t fall behind the machine table. (see Fig. 3-5)

      One time I screwed up one of the sheet metal covers that cover the back column. I failed to remove a remnant that had fallen behind the machine table. When the table moved toward the column while a program was running, the remnant got jammed between the machine table and the cover, which destroyed the cover. Lesson learned.

Figure 3-4 This is a short program showing M01 Optional Stop commands inserted in the code before the tool change commands T2 M06 and T3 M06. If the Optional Stop button on the controller is activated, the machine will stop executing the program when the controller reads the M01 commands. Optional Stops are generally used for debugging and proofing programs because they give the machinist a chance to see how the last tool ran.

Figure 3-5 Large remnants can get jammed between the table and the back column of the machine. It’s a condition that must be avoided.

      9.Program drilled pilot holes deep enough so reamers won’t jam.

      The pilot hole for a reamer has to be drilled deep enough so that the reamer won’t jam against the bottom of the pilot hole. When you have blind reamed holes, it is a good idea to check the program at the machine to make sure pilot holes are drilled deep enough to avoid this interference.

      10.Be extra cautious when using tie-down clamps. (see Fig. 3-6)

      Except for simple setups, I try to avoid using tie-down clamps unless I know there is little chance of running into them. Besides just sticking up in harms way, they are too often placed inconsistently by operators. Instead of using tie-down clamps, I prefer bolting parts down. I try to avoid special programming that may be needed to “jump” over clamps. These special programs can be nightmares for someone trying to set up the job at a later date.

      11.Be cautious of protruding bolt heads. (see Fig. 3-7)

      With bolts, a default rapid plane of one inch is usually adequate to jump from one location to the next without having to concern yourself with interference — as long as the bolt heads don’t stick up higher than the rapid plane.

Figure 3-6 Tie-down clamps are something that can easily be run into. When using tie-down clamps, program using generous rapid planes.

Figure 3-7 Bolting parts down for machining is preferable to using tie-down clamps because bolt heads don’t stick up as high and are used in consistent locations.

      12.If a tap breaks while you’re at the machine, hit either the “Emergency Stop” button or the “Reset” button.

      Once the machine starts executing a G84 tapping canned cycle, pressing the “Feed Hold” button will not stop the spindle from continuing its journey to tap the hole. This can make a bad situation worse as the broken tap, which is still in the tool holder, grinds into the portion of the tap that is broken off in the part.

      13.When mounting cutters in tool holders, make sure all cutters extend far enough below the tool holder so the holder doesn’t interfere with the part when the program is run. (see Fig. 3-8)

      This is a common crash, one that can easily be avoided if the machinist takes a little time to understand what features a tool is going to cut and how deep the cutter will be going. Most setup sheets provide this information.

      I would be a nervous wreck running somebody’s unproven program until I fully understood what feature a tool was going to cut. Sometimes cutter depths are obvious by looking at the drawing. Other times — especially when there are many tools and the part is complicated — it’s not so obvious. If you have the option and the experience, it is best to check how deep the cutters will be going by referring to the CAD model and the CAM simulation.

      Standard center drills are relatively short. Be especially careful with standard center drills in order to avoid tool holder interference. You СКАЧАТЬ