High-Performance Materials from Bio-based Feedstocks. Группа авторов

Чтение книги онлайн.

Figure 2.10 Hydrolysis of cellulose.

      Aside from the hydrolysis reaction, a sugar‐derived solid catalyst was found to have potential in biodiesel production by esterification. The D‐glucose‐derived sugar acid catalyst was compared with conventional solid catalysts (sulfated zirconia, Amberlyst‐15, and niobic acid) for its effectiveness to esterify a short‐chain aliphatic alcohol with palmitic acid and oleic acid [147]. The sugar‐derived acid catalyst presented superb thermal stability and the highest activity among other acid catalysts, and its activity was almost the same as a homogeneous acid catalyst. To contribute to the cost‐competition, the sugar catalyst was used in biodiesel production from waste oil with high free fatty acid content (27.8%). It showed prominent performances in the reactivity with a yield of higher than 90%, in spite of the oil containing high amounts of free fatty acids.

      2.5.6 Carbon Nanotubes from Biomass

      CNTs, which are a 3D‐structured material, have recently been developed for their application in catalysis due to the promising physical and chemical properties. Several kinds of carbon‐rich biomasses and bio‐resource residues were used as feedstock in the production of biomass‐derived CNTs. Yao et al. utilized a biomass residue from the liquor industry to produce CNTs by activation and carbonization to receive an activated carbon followed by thermal condensation [148]. The activated carbon was reacted with dicyandiamide and Ni metal precursor and subsequently annealed at 700, 800, or 900 °C to embed the Ni nanoparticles in the N‐doped CNTs supported on porous carbon (Ni‐CNTs‐C). The growth of CNTs on the surface of the porous carbon support was promoted by the increasing annealing temperature. The bamboo‐like structure of CNTs annealed at 700 °C had a diameter of approximately 10–15 nm and a length of 100–300 nm. Conversely, the surface area was decreased from 558 to 283 m² g⁻¹ when the annealing temperature was raised from 700 to 900 °C. The Ni‐CNTs‐C annealed at 700 °C revealed the highest catalytic activity with ~98.2% removal of organic dye (Orange II) within 90 minutes because its largest surface area provided more active sites. The dye removal percentage was reduced to 96.9 and 68.5% with annealing at 800 and 900 °C, respectively. Leaching and agglomeration of Ni⁰ and CNTs were shielded by the carbon layer leading to high stability and activity of these catalysts in acidic media. The activity of the reused catalyst, however, decreased from 98.2 to 64.2% after five cycles. The great number of CNTs presented both a high number of active sites and promoted electron transfer on the carbon surface. The Ni‐CNTs‐C catalyst was also tested for its performance in the conversion of harmful Cr(VI) to less toxic Cr(III). Among catalysts tested, the catalyst annealed at 800 °C (Ni‐CNTs‐C‐800) showed the highest activity and could completely reduce Cr(VI) to Cr(III) in 160 minutes as observed from the change in color from yellow to colorless [148].

The HTC of biomass including sugar, cellulose, and crude plants yields many intermediate products of liquid alkanes such as 5‐hydroxymethyl‐2‐furaldehyde, furfural, 5‐methylfurfural and 1,2,4‐benezenetriol. When these intermediates have the appropriate concentration of oxygenated functional groups, they could self‐transform into various structures of carbonaceous materials through various conversion pathways, i.e. dehydration, aromatization, and polymerization. The occurring carbonaceous particles could attach to the CNT matrix, and repeatedly bind layer‐by‐layer to obtain oxygenated functional groups anchored to the CNTs. The resulting material is suitable both as a direct catalyst and as support for metal catalysts as it contained numerous reactive functional groups. The metal immobilized on the functionalized CNT catalyst presented both high activity and selectivity for the hydrogenation of unsaturated aldehyde to unsaturated alcohol with 90% selectivity at a conversion of 55% [149].

      2.5.7 Graphene and Its Derivatives

Graphene, a member of the graphite family, is a flat monolayer of carbon atoms arranged into a 2D honeycomb structure. Graphene and graphene‐based materials (e.g. graphene oxides) have been extensively exploited because of their excellent thermal, mechanical, and electronic characteristics. Graphene, both with and without modifications, has been explored for its effectiveness in various reactions. Graphene produced from biomass commonly contains a high content of impurities that could either act as a poison or as a natural promoter in catalysis [150]. The imperfect graphene contaminated with nitrogen dopant was active and stable for the selective CO₂ hydrogenation to methane. For example, the natural N‐doped graphene prepared by pyrolysis of chitosan at 500 °C showed a higher CO₂ conversion than other dopants and 99.2% selectivity toward CH₄ [151]. Alternatively, external N doping into graphene was employed as a metal‐free catalyst which also showed high stability and selectivity in hydrogenation [77]. Huang et al. [152] synthesized N‐doped graphene via the carbonization of biomass guanine along with colloidal silica at 1000 °C under N₂ atmosphere followed by the addition of hydrofluoric acid to remove the silica template. It was observed that its electrochemical activity in the oxygen reduction reaction under acid and base conditions was remarkable due to its porous structure and high N doping [152]. Other than N doping onto graphene, an Ru metal‐supported graphene synthesized via carbonization and calcination of a mixture of glucose, FeCl₃, and RuCl₃ also demonstrated to be highly effective for levulinic acid hydrogenation to γ‐valerolactone (see Figure 2.11) with 100% conversion and 96% yield [153]. In addition, a catalyst based on graphene‐encapsulated Fe₃C embedded in CNTs was successfully produced using the inexpensive co‐pyrolysis of a mixture of biomass (glucose, xylitol, or sucrose), melamine, and iron compound [77]. The functionalized CNTs were stable and efficient in the hydrogenation of nitrobenzene to anilines. The 100% conversion of nitrobenzene along with nearly 99% selectivity toward anilines was achieved with the catalyst that was carbonized at 700 °C. The catalytic activity of this catalyst was mainly based on the pyrolysis temperature; the Fe₃C, which represents the active site for this reaction, could be destroyed when the pyrolysis temperature reached over 700 °C.

2.6 Summary and Future Aspects

The exponentially growing development in the transformation of biomass into carbon‐based materials is presented in a СКАЧАТЬ