Patty's Industrial Hygiene, Physical and Biological Agents. Группа авторов

Чтение книги онлайн.

FIGURE 6 The absurdity of testing laser eye protectors to withstand kilowatt laser beams.

      The ANSI standards subcommittee, SSC‐7, that prepared ANSI Z136.7 was particularly interested in developing standardized test methods for newer types of eye‐protectors. Many newer designs employ reflective technologies, such as holographic reflectors, since the true level of protection of such multi‐wavelength designs depend upon pupil diameter, eye movements, a fit tolerance, and eye relief as well as simply the optical properties of the filter. These require very involved point‐by‐point testing over the surface for these sophisticated filter systems.

To minimize the cost and complexity of filter‐material damage thresholds, the ANSI Z136.7 standard introduced the concept of default damage (failure) threshold values for substrate materials, where – unless the manufacturer wanted to claim substantially higher laser‐induced damage thresholds – damage testing would not be required. Values for plastics, glass, and quartz were specified, and the manufacturer could refer to these time‐dependent damage‐threshold values without the need for testing each product. As an example, the failure threshold value (TV_max) for polycarbonate lenses is given as 10 J cm⁻² for pulse durations t < 1 ms and 300 t^0.5 J cm⁻² for t > 1 ms. Glass and quartz have higher values of TV_max for CW lasers, but actually somewhat lower TV_max for short pulse durations. Of course, testing for saturable absorption (transient, reversible bleaching) of absorbers from very‐short‐pulse lasers would always be required, and radiant exposure test levels for Q‐switched and mode‐locked laser pulses are provided. The ANSI TSC‐7 subcommittee members felt that it was inappropriate to place much emphasis on substrate damage of goggle materials at levels well above skin injury thresholds, and hopefully this issue, which has been around for decades, will soon be forgotten (11, 24, 25).

8 LASER BARRIERS

Laser barriers are defined in the ANSI Z136.7 standard as “moveable or fixed equipment (devices) used to block or attenuate laser energy,” include curtains or shields that are used for enclosing a “laser controlled area” (see Figure 6). Laser curtains are particularly useful for nonpermanent laser operational situations; for example, where they are put up at an entryway to enclose a “temporary laser controlled area” during servicing. The ANSI Z136.7 standard places a number of obviously important requirements on the materials used in laser barriers, e.g. the material should not be flammable or emit toxic by‐products when irradiated. The manufacturer should specify the material damage threshold for a given time (traditionally 60 or 100 seconds, but now standardized at 100 seconds). This “barrier threshold limit” (TL), or damage threshold, for a fabric curtain ranges between approximately 5 and 350 W cm⁻². For metal barriers, the TL will typically be of the order of approximately 1200 W cm⁻² for three minutes. Active barriers, such as those with built‐in sensors to shut down laser operation before the barrier fails, have TL values with very high irradiances (Figure 7).

      The ANSI Z136.7 standard is not just for the manufacturer of protective eyewear and barriers. The LSO is tasked with the potential need to calculate the separation distance, D_s, of the laser from the barrier if the maximum laser beam irradiance exceeds the TL of the barrier. Typically, in large industrial material processing applications the beam is focused and the beam irradiance decreases rapidly beyond the beam's focal point, and this calculation becomes both useful and necessary.

      Manufacturer testing protocols for the TL are provided to determine the highest irradiance incident on a laser barrier for which no penetration occurs for an exposure of 100 seconds and at a specified exposure diameter ranging between 3 and 10 mm. In addition, the test should report the “first visible damage,” or FVD, such as a visually observable change or structural alteration in the protective barriers surface (melting, pitting, cracking, discoloration, and so on) that occurs during or following the exposure; and any flame, smoke or a sign of thermal distortion should be recorded and airborne contaminants must be captured and analyzed for toxic content. A penetration threshold level (PTL) is also to be recorded; this is the initial power level at which beam breakthrough of the material occurs.

      The ANSI Z136.7 standard also lists requirements for the manufacturer to provide certain information to the user of a barrier, such as any limitations of use, such as certain applications. A description of an eye‐protective filter optical density with the angular protection afforded by a reflective filter, if applicable, must accompany eyewear. In addition, both groups of products must be appropriately labeled and directions for storage, care, cleaning, and periodic inspections, including any chemical‐exposure warnings are to be provided.